FRP Square Shape Cooling Towers Manufacturers

FRP Square Shape Cooling Towers

FRP Square type Cooling Towers operates on the induced draft counter flow principle operation. The fan creates air movement vertically pulled upwards on tower across the fills in opposition to the water flow.

Hot circulating water enters the water inlet headers and sprays through non clogging PP spray nozzle. Water distribution is even. Well designed PVC Drift Eliminators are fitted to reduce Drift Losses. Square Fiber Glass Cooling Towers are provided with Inspection door for easy access for inspection and maintenance.



DESCRIPTION

The Square Shape Cooling Towers designed It is with uniform water distribution & excellent heat transfer. The Cooling Towers consists of Virgin Honey comb PVC fills and Drift Eliminators in a design that maximizes economy and efficiency & directly driven fan & Motor with spray Nozzles 'Minimum drifts Losses. Hot dipped Galvanized hardware with rectangular casing body in elegant design. Our experts test these products on the grounds of durability and functionality.Further, we provide custom made facility on this Square Cooling Tower to our valuable customers at affordable rates.

Square shape cooling towers Square Type Cooling Towers

INSTALLATION OF FRP SQUARE SHAPE COOLING TOWERS

Towers of lower capacity are completely factory assembled before despatch. At site the tower has just to be bolted, on the RCC / brick masonry foundation, thus saving a lot of installation time. Towers of higher capacity can easily be assembled at site and then installed in a manner similar to small towers. Maintenance is considerably reduced because fan, sprinkler fill and eliminator can easily be approached from the top without disturbing the cooling tower casing.

FRP Bottle Shape Cooling Towers Manufacturers
Draught Type/ SHAPE Flow Type MOC Water Flow Rate (LPM) Fill type Drive Type
Induced / SQUARE Counter Flow FRP 100 – 10,000 Honeycomb Fills Direct

FRP SQUARE SHAPE COOLING TOWERS CONSTRUCTION MATERIAL

ITEM MATERIAL USED
Frame MS HDGS (Hot-dip galvanized U-steel)
Casing F.R.P.
Water basin F.R.P.
Distributing system HDGS & PVC
Fan Polypropylene or Aluminium alloy
Motor Fully enclosed waterproof type
Honeycomb Fills PVC/ABS
Connections Flange


FRP CASING :

Cooling Tower Casing is made of selected grade materials of tough Fiber Glass Reinforced Polyster and resins etc. An additional embossing is provided for extra strength of large Cooling Towers



FRP BASIN :

The water basin like the tower casing is made of FRP. It is bowl shaped, with a cylindrical auxiliary suction tank at the bottom. This construction eliminates the danger of drawing airinto the pump when operating with minimum water in the basin. A drain is provided to facilitate the removal if accumulated dirt from the bottom of the tank. The bowl shape of the water basin facilitates the cleaning of the tower interior.

PVC FILLS :

The fillings are made of PVC.They have excellent heat exchange efficiency & remarkably good chemical resistance. These fills are totally enclosed in the tower, thus excluding them from sunlight and minimizing the growth of algae.A pre-eminent quality and long life fill consists of modular block of PVC honey combs construction to create prolongedcontact time of hot air with water for maximum heat transfer.

HEADER PIPE :

The Header pipes are used for co-current water distribution systems. Air and water both travel together in the same direction from top to bottom. Hot water is allowed to spray through specially designed nylon/pp nozzles at minimum 0.5 kg./ sq. cm pressure. Water enters nozzle tangentially at top and is given spiral action in spiral chamber.

SPRAY NOZZLES :

The performance of cooling tower greatly depends upon the water distribution over the fills. SCSP nozzles distribute water evenly through a wide spray angle without any dry pockets. They are lightweight and reduce the frequency of clogging. The Solid Cone Square Pattern (SCSP) nozzles produce a solid cone spray of water that is Distributed in a square pattern onto the fills.

DRIFT ELIMINATOR :

Reduces carry over losses of water. The eliminator is of rigid PVC (Applicable for square type cooling tower). The individual drift eliminators of S-shaped corrugated sheets are bonded with subsequent layers to create the structure. The entire area is thus divided into several fine S shaped mini zones each removing water droplets on the entire surface of the cell.

Aluminum /FRP AXIAL FAN :

Specially designed energy efficient fans are of induced-draft axial type with adjustable pitch. Material chosen arenon corrosive of plastic, FRP or aluminium alloy. The high efficiency design ensures low running cost and the lowest possible noise level. Fan blade pitch is factory set and dynamically balanced.



MOTORS :

The motors are totally enclosed (IP55), flange type, 415 V, 3 ph, 50 Hz, induction weather proof with SS304 extended shaft and are specially designed for cooling tower application.



MOTORIZED GEAR BOX :

This gearbox series for cooling towers and/or pulp and paper mixers is especially built to grant reliability to customers. This is made possible through a generous upsizing of both gears and bearings as well as a balanced internal gear arrangement, so to offeroptimization of uniformity in balancing loads inside the gearbox. With the half casing the periodic inspection and maintenance purposes are facilitated, especially in places that are not easy to access.