FRP Bottle Shape Cooling Towers Manufacturers

FRP Bottle Shape Cooling Towers

The FRP Bottle Shape Cooling Towers (Fibre glass Reinforced Plastic) also called as Round Shape Cooling Tower. The casing and basins are designed to withstand severe vibration, high wind load and to resist corrosion. The Cooling Tower consists of Honey comb PVC fills and eliminators in a design that maximizes economy and efficiency and directly driven fan and Motor 'Minimum drift Losses’. Uniform distribution of hot water by rotating arm sprinkler. Hot dipped Galvanized hardware to withstand wind forces. The bottle shape makes possible to provide maximum cooling efficiency in minimum plan area with lower energy consumption.


INSTALLATION

Towers of lower capacity are completely factory assembled before despatch. At site the tower has just to be bolted, on the RCC / brick masonry foundation, thus saving a lot of installation time. Towers of higher capacity can easily be assembled at site and then installed in a manner similar to small towers. Maintenance is considerably reduced because fan, sprinkler fill and eliminator can easily be approached from the top without disturbing the cooling tower casing.

FRP Bottle Shape Cooling Towers Manufacturers
Draught Type/ SHAPE Flow Type MOC Water Flow Rate (LPM) Fill type Drive Type
Induced / ROUND Counter Flow FRP 100 – 10,000 Honeycomb Fills Direct

FRP BOTTLE SHAPE COOLING TOWERS CONSTRUCTION MATERIAL

ITEM MATERIAL USED
Frame MS HDGS (Hot-dip galvanized U-steel)
Casing F.R.P.
Water basin F.R.P.
Distributing system HDGS & PVC
Fan Polypropylene or Aluminium alloy
Motor Fully enclosed waterproof type
Honeycomb Fills PVC/ABS
Connections Flange


FRP CASING

Cooling Tower Casing is made of selected grade materials of tough Fibre Glass Reinforced Polyester & resins, etc. Additional embossing is done for extra strength in case of big cooling towers.

FRP BASIN

The water basin like the tower casing is made of FRP. It is bowl shaped, with a cylindrical Auxiliary suction tank at the bottom. This construction eliminates the danger of drawing air into the pump when operating with minimum water in the basin. A drain is provided to Facilitate the removal if accumulated dirt from the bottom of the tank. The bowl shape of the water basin facilitates the cleaning of the tower interior.



HONEY COMB FILLS

PVC Honeycomb type fills having extended contact area. Splits incoming air and water into several streams spread evenly across the water cross section increasing heat transfer rate easy to replace.





AUTOMATIC ROTATING SPRINKLER

Uniform distribution of water over the honeycomb Fills is achieved by means of automatic water sprinkler. Specially designed rotary sprinkler head is made of PVC/aluminium alloy to avoid corrosion, also fitted with sealed ball bearings to take care of thrust & radial loads. S.S. & Brass sprinklers are also provided at an extra cost.

DISTRIBUTION PIPES

The Hot water-distribution pipe is located inside a Cooling tower and delivers potable Water to the fixtures. The water supply delivering through water sprinkler and fall In to the distribution Pipe. In water distribution Pipes we made holes for hot water spillage. All PVC pipes used in distribution systems of the cooling towers are standard make and tested Per IS 4985.

ALUMINIUM FRP AXIAL FAN

An aerodynamically designed axial flow type fan is specifically designed for cooling tower use. A well balanced fan delivers large air volume at high efficiency and low noise level. The fan blades and hub are of cast aluminium alloy (LM-6). The direct driven fan with Variable pitched blades. Fans are coupled to slow speed weather proof motor in IP-55 Construction. The mechanical equipment is so designed that maintenance of motor and fan Blades can easily be carried out without removal of the entire system.

COOLING TOWER EXTENDED SHAFT MOTOR

The Special Type Totally Enclosed Flange Mounted Motors, With Extended Threaded Shaft And Sealed Top Is Supplied With Cooling Tower. The Motor Is Having Totally Weather Proof Ip - 55 Degree Of Protection, suitable Cold & Hot And Humidity Atmosphere. Motor Hp Will Be Determined By The Calculated Thermal Requirement

COOLING TOWER MOTORIZED GEAR BOX

We Offer Cooling Tower Gearboxes. Case Hardened and Lapped steel spiral bevel gears to transmit the torque between right angle shaft. Unicase design with Pumpless Lubrication and three-point Foundation. Applications: FRP Cooling Tower, Wooden Cooling tower Industry : Plastic and steel Industry, Sugar, Cement, Paper, Solvent Extraction, Power Plants, Mineral Processing, etc.

COOLING TOWER STRUCTURE

One of the most commonly used Cooling Tower Material is Galvanized Steel. As G-235 hot dipped Galvanized Steel provides corrosion resistance, durable and long service life and also is the symbol of great structural strength.. And the frame is stable and with good rigidity, the load is evenly distributed among each foundation, which makes operation and assembly easily